BusyBox - The Swiss Army Knife of Embedded Linux
busybox <applet> [arguments...] # or
<applet> [arguments...] # if symlinked
BusyBox combines tiny versions of many common UNIX utilities into a single small executable. It provides minimalist replacements for most of the utilities you usually find in GNU coreutils, util-linux, etc. The utilities in BusyBox generally have fewer options than their full-featured GNU cousins; however, the options that are included provide the expected functionality and behave very much like their GNU counterparts.
BusyBox has been written with size-optimization and limited resources in mind. It is also extremely modular so you can easily include or exclude commands (or features) at compile time. This makes it easy to customize your embedded systems. To create a working system, just add /dev, /etc, and a Linux kernel. BusyBox provides a fairly complete POSIX environment for any small or embedded system.
BusyBox is extremely configurable. This allows you to include only the components you need, thereby reducing binary size. Run 'make config' or 'make menuconfig' to select the functionality that you wish to enable. Then run 'make' to compile BusyBox using your configuration.
After the compile has finished, you should use 'make install' to install BusyBox. This will install the 'bin/busybox' binary, in the target directory specified by CONFIG_PREFIX. CONFIG_PREFIX can be set when configuring BusyBox, or you can specify an alternative location at install time (i.e., with a command line like 'make CONFIG_PREFIX=/tmp/foo install'). If you enabled any applet installation scheme (either as symlinks or hardlinks), these will also be installed in the location pointed to by CONFIG_PREFIX.
BusyBox is a multi-call binary. A multi-call binary is an executable program that performs the same job as more than one utility program. That means there is just a single BusyBox binary, but that single binary acts like a large number of utilities. This allows BusyBox to be smaller since all the built-in utility programs (we call them applets) can share code for many common operations.
You can also invoke BusyBox by issuing a command as an argument on the command line. For example, entering
/bin/busybox ls
will also cause BusyBox to behave as 'ls'.
Of course, adding '/bin/busybox' into every command would be painful. So most people will invoke BusyBox using links to the BusyBox binary.
For example, entering
ln -s /bin/busybox ls
./ls
will cause BusyBox to behave as 'ls' (if the 'ls' command has been compiled into BusyBox). Generally speaking, you should never need to make all these links yourself, as the BusyBox build system will do this for you when you run the 'make install' command.
If you invoke BusyBox with no arguments, it will provide you with a list of the applets that have been compiled into your BusyBox binary.
Most BusyBox applets support the --help argument to provide a terse runtime description of their behavior. If the CONFIG_FEATURE_VERBOSE_USAGE option has been enabled, more detailed usage information will also be available.
Currently available applets include:
[, [[, adjtimex, ar, arp, arping, ash, awk, basename, bbconfig,
beep, blkid, brctl, bunzip2, bzcat, bzip2, cal, cat, catv, chat,
chattr, chgrp, chmod, chown, chpst, chroot, chrt, chvt, cksum,
clear, cmp, comm, cp, cpio, crond, crontab, cttyhack, cut, date, dc,
dd, deallocvt, depmod, devmem, df, dhcprelay, diff, dirname, dmesg,
dnsd, dnsdomainname, dos2unix, dpkg, dpkg-deb, du, dumpkmap,
dumpleases, echo, ed, egrep, eject, env, envdir, envuidgid,
ether-wake, expand, expr, fakeidentd, false, fbset, fbsplash,
fdflush, fdformat, fdisk, fgrep, find, findfs, fold, free,
freeramdisk, fsck, fsck.minix, fsync, ftpd, ftpget, ftpput, fuser,
getopt, grep, gunzip, gzip, halt, hd, hdparm, head, hexdump, hostid,
hostname, httpd, hush, hwclock, id, ifconfig, ifdown, ifenslave,
ifplugd, ifup, inetd, init, insmod, install, ionice, ip, ipaddr,
ipcalc, ipcrm, ipcs, iplink, iproute, iprule, iptunnel, kbd_mode,
kill, killall, killall5, klogd, last, length, less, linux32,
linux64, linuxrc, ln, loadfont, loadkmap, logger, logname, logread,
losetup, lpd, lpq, lpr, ls, lsattr, lsmod, lspci, lsusb, lzmacat,
lzop, lzopcat, makedevs, makemime, man, md5sum, mdev, mesg,
microcom, mkdir, mkdosfs, mkfifo, mkfs.minix, mkfs.reiser,
mkfs.vfat, mknod, mkswap, mktemp, modprobe, more, mount, mountpoint,
msh, mt, mv, nameif, nc, netstat, nice, nmeter, nohup, nslookup,
ntpd, od, openvt, patch, pgrep, pidof, ping, ping6, pipe_progress,
pivot_root, pkill, popmaildir, poweroff, printenv, printf, ps,
pscan, pwd, raidautorun, rdate, rdev, readahead, readlink,
readprofile, realpath, reboot, reformime, renice, reset, resize, rm,
rmdir, rmmod, route, rpm, rpm2cpio, rtcwake, run-parts, runlevel,
runsv, runsvdir, rx, script, scriptreplay, sed, sendmail, seq,
setarch, setconsole, setfont, setkeycodes, setlogcons, setsid,
setuidgid, sh, sha1sum, sha256sum, sha512sum, showkey, slattach,
sleep, softlimit, sort, split, start-stop-daemon, stat, strings,
stty, sum, sv, svlogd, swapoff, swapon, switch_root, sync, sysctl,
syslogd, tac, tail, tar, taskset, tcpsvd, tee, telnet, telnetd,
test, tftp, tftpd, time, timeout, top, touch, tr, traceroute,
traceroute6, true, tty, ttysize, tunctl, udhcpc, udhcpd, udpsvd,
umount, uname, uncompress, unexpand, uniq, unix2dos, unlzma, unlzop,
unzip, uptime, usleep, uudecode, uuencode, vconfig, vi, volname,
wall, watch, watchdog, wc, wget, which, who, whoami, xargs, yes,
zcat, zcip
adjtimex [-q] [-o offset] [-f frequency] [-p timeconstant] [-t tick]
Read and optionally set system timebase parameters. See adjtimex(2).
Options:
-q Quiet
-o offset Time offset, microseconds
-f frequency Frequency adjust, integer kernel units (65536 is 1ppm)
(positive values make clock run faster)
-t tick Microseconds per tick, usually 10000
-p timeconstant
ar [-o] [-v] [-p] [-t] [-x] ARCHIVE FILES
Extract or list FILES from an ar archive
Options:
-o Preserve original dates
-p Extract to stdout
-t List
-x Extract
-v Verbose
| arp | |
| [-vn] | [-H type] [-i if] -a [hostname] |
| [-v] | [-i if] -d hostname [pub] |
| [-v] | [-H type] [-i if] -s hostname hw_addr [temp] |
| [-v] | [-H type] [-i if] -s hostname hw_addr [netmask nm] pub |
| [-v] | [-H type] [-i if] -Ds hostname ifa [netmask nm] pub |
Manipulate ARP cache
Options:
-a Display (all) hosts
-s Set new ARP entry
-d Delete a specified entry
-v Verbose
-n Don't resolve names
-i IF Network interface
-D Read <hwaddr> from given device
-A, -p AF Protocol family
-H HWTYPE Hardware address type
arping [-fqbDUA] [-c count] [-w timeout] [-I dev] [-s sender] target
Send ARP requests/replies
Options:
-f Quit on first ARP reply
-q Quiet
-b Keep broadcasting, don't go unicast
-D Duplicated address detection mode
-U Unsolicited ARP mode, update your neighbors
-A ARP answer mode, update your neighbors
-c N Stop after sending N ARP requests
-w timeout Time to wait for ARP reply, in seconds
-I dev Interface to use (default eth0)
-s sender Sender IP address
target Target IP address
awk [OPTIONS] [AWK_PROGRAM] [FILE]...
Options:
-v VAR=VAL Set variable
-F SEP Use SEP as field separator
-f FILE Read program from FILE
basename FILE [SUFFIX]
Strip directory path and .SUFFIX from FILE
bbconfig
Print the config file which built busybox
beep -f FREQ -l LEN -d DELAY -r COUNT -n
Options:
-f Frequency in Hz
-l Length in ms
-d Delay in ms
-r Repetitions
-n Start new tone
blkid
Print UUIDs of all filesystems
brctl COMMAND [BRIDGE [INTERFACE]]
Manage ethernet bridges
Commands:
show Show a list of bridges
addbr BRIDGE Create BRIDGE
delbr BRIDGE Delete BRIDGE
addif BRIDGE IFACE Add IFACE to BRIDGE
delif BRIDGE IFACE Delete IFACE from BRIDGE
setageing BRIDGE TIME Set ageing time
setfd BRIDGE TIME Set bridge forward delay
sethello BRIDGE TIME Set hello time
setmaxage BRIDGE TIME Set max message age
setpathcost BRIDGE COST Set path cost
setportprio BRIDGE PRIO Set port priority
setbridgeprio BRIDGE PRIO Set bridge priority
stp BRIDGE [1|0] STP on/off
bunzip2 [OPTIONS] [FILE]
Uncompress FILE (or standard input)
Options:
-c Write to standard output
-f Force
bzcat FILE
Uncompress to stdout
bzip2 [OPTIONS] [FILE]...
Compress FILEs (or standard input) with bzip2 algorithm.
Options:
-c Write to standard output
-d Decompress
-f Force
-1..-9 Compression level
cal [-jy] [[month] year]
Display a calendar
Options:
-j Use julian dates
-y Display the entire year
cat [-u] [FILE]...
Concatenate FILEs and print them to stdout
Options:
-u Use unbuffered i/o (ignored)
catv [-etv] [FILE]...
Display nonprinting characters as ^x or M-x
Options:
-e End each line with $
-t Show tabs as ^I
-v Don't use ^x or M-x escapes
chat EXPECT [SEND [EXPECT [SEND...]]]
Useful for interacting with a modem connected to stdin/stdout. A script consists of one or more "expect-send" pairs of strings, each pair is a pair of arguments. Example: chat '' ATZ OK ATD123456 CONNECT '' ogin: pppuser word: ppppass '~'
chattr [-R] [-+=AacDdijsStTu] [-v VERSION] [FILE]...
Change file attributes on an ext2 fs
Modifiers:
- Remove attributes
+ Add attributes
= Set attributes
Attributes:
A Don't track atime
a Append mode only
c Enable compress
D Write dir contents synchronously
d Don't backup with dump
i Cannot be modified (immutable)
j Write all data to journal first
s Zero disk storage when deleted
S Write file contents synchronously
t Disable tail-merging of partial blocks with other files
u Allow file to be undeleted
Options:
-R Recurse
-v Set the file's version/generation number
chgrp [-RhLHPcvf]... GROUP FILE...
Change the group membership of each FILE to GROUP
Options:
-R Recurse
-h Affect symlinks instead of symlink targets
-L Traverse all symlinks to directories
-H Traverse symlinks on command line only
-P Don't traverse symlinks (default)
-c List changed files
-v Verbose
-f Hide errors
chmod [-Rcvf] MODE[,MODE]... FILE...
Each MODE is one or more of the letters ugoa, one of the symbols +-= and one or more of the letters rwxst
Options:
-R Recurse
-c List changed files
-v List all files
-f Hide errors
chown [-RhLHPcvf]... OWNER[<.|:>[GROUP]] FILE...
Change the owner and/or group of each FILE to OWNER and/or GROUP
Options:
-R Recurse
-h Affect symlinks instead of symlink targets
-L Traverse all symlinks to directories
-H Traverse symlinks on command line only
-P Don't traverse symlinks (default)
-c List changed files
-v List all files
-f Hide errors
| chpst [-vP012] [-u USER[:GRP]] [-U USER[:GRP]] [-e DIR] | |
| [-/ DIR] [-n NICE] [-m BYTES] [-d BYTES] [-o N] | |
| [-p N] [-f BYTES] [-c BYTES] PROG ARGS |
Change the process state and run PROG
Options:
-u USER[:GRP] Set uid and gid
-U USER[:GRP] Set $UID and $GID in environment
-e DIR Set environment variables as specified by files
in DIR: file=1st_line_of_file
-/ DIR Chroot to DIR
-n NICE Add NICE to nice value
-m BYTES Same as -d BYTES -s BYTES -l BYTES
-d BYTES Limit data segment
-o N Limit number of open files per process
-p N Limit number of processes per uid
-f BYTES Limit output file sizes
-c BYTES Limit core file size
-v Verbose
-P Create new process group
-0 Close standard input
-1 Close standard output
-2 Close standard error
chroot NEWROOT [PROG [ARGS]]
Run PROG with root directory set to NEWROOT
chrt [OPTIONS] [PRIO] [PID | PROG [ARGS]]
Manipulate real-time attributes of a process
Options:
-p Operate on PID
-r Set SCHED_RR scheduling
-f Set SCHED_FIFO scheduling
-o Set SCHED_OTHER scheduling
-m Show min and max priorities
chvt N
Change the foreground virtual terminal to /dev/ttyN
cksum FILES...
Calculate the CRC32 checksums of FILES
clear
Clear screen
cmp [-l] [-s] FILE1 [FILE2 [SKIP1 [SKIP2]]]
Compares FILE1 vs stdin if FILE2 is not specified
Options:
-l Write the byte numbers (decimal) and values (octal)
for all differing bytes
-s Quiet
comm [-123] FILE1 FILE2
Compare FILE1 to FILE2, or to stdin if - is specified
Options:
-1 Suppress lines unique to FILE1
-2 Suppress lines unique to FILE2
-3 Suppress lines common to both files
cp [OPTIONS] SOURCE DEST
Copy SOURCE to DEST, or multiple SOURCE(s) to DIRECTORY
Options:
-a Same as -dpR
-R,-r Recurse
-d,-P Preserve symlinks (default if -R)
-L Follow all symlinks
-H Follow symlinks on command line
-p Preserve file attributes if possible
-f Force overwrite
-i Prompt before overwrite
-l,-s Create (sym)links
cpio [-dmvu] [-F FILE] [-H newc] [-tio] [-p DIR]
Extract or list files from a cpio archive, or create an archive (-o) or copy files (-p) using file list on standard input
Main operation mode:
-t List
-i Extract
-o Create (requires -H newc)
-p DIR Copy files to DIR
Options:
-d Make leading directories
-m Preserve mtime
-v Verbose
-u Overwrite
-F FILE Input (-t,-i,-p) or output (-o) file
-H newc Archive format
crond -fbS -l N -d N -L LOGFILE -c DIR
-f Foreground
-b Background (default)
-S Log to syslog (default)
-l Set log level. 0 is the most verbose, default 8
-d Set log level, log to stderr
-L Log to file
-c Working dir
crontab [-c DIR] [-u USER] [-ler]|[FILE]
-c Crontab directory
-u User
-l List crontab
-e Edit crontab
-r Delete crontab
FILE Replace crontab by FILE ('-': stdin)
cut [OPTIONS] [FILE]...
Print selected fields from each input FILE to standard output
Options:
-b LIST Output only bytes from LIST
-c LIST Output only characters from LIST
-d CHAR Use CHAR instead of tab as the field delimiter
-s Output only the lines containing delimiter
-f N Print only these fields
-n Ignored
date [OPTIONS] [+FMT] [TIME]
Display time (using +FMT), or set time
Options:
[-s,--set] TIME Set time to TIME
-u,--utc Work in UTC (don't convert to local time)
-R,--rfc-2822 Output RFC-2822 compliant date string
-I[SPEC] Output ISO-8601 compliant date string
SPEC='date' (default) for date only,
'hours', 'minutes', or 'seconds' for date and
time to the indicated precision
-r,--reference FILE Display last modification time of FILE
-d,--date TIME Display TIME, not 'now'
-D FMT Use FMT for -d TIME conversion
Recognized TIME formats:
hh:mm[:ss]
[YYYY.]MM.DD-hh:mm[:ss]
YYYY-MM-DD hh:mm[:ss]
[[[[[YY]YY]MM]DD]hh]mm[.ss]
dc expression...
Tiny RPN calculator. Operations: +, add, -, sub, *, mul, /, div, %, mod, **, exp, and, or, not, eor, p - print top of the stack (without altering the stack), f - print entire stack, o - pop the value and set output radix (value must be 10 or 16). Examples: 'dc 2 2 add' -> 4, 'dc 8 8 * 2 2 + /' -> 16.
| dd [if=FILE] [of=FILE] [ibs=N] [obs=N] [bs=N] [count=N] [skip=N] | |
| [seek=N] [conv=notrunc|noerror|sync|fsync] |
Copy a file with converting and formatting
Options:
if=FILE Read from FILE instead of stdin
of=FILE Write to FILE instead of stdout
bs=N Read and write N bytes at a time
ibs=N Read N bytes at a time
obs=N Write N bytes at a time
count=N Copy only N input blocks
skip=N Skip N input blocks
seek=N Skip N output blocks
conv=notrunc Don't truncate output file
conv=noerror Continue after read errors
conv=sync Pad blocks with zeros
conv=fsync Physically write data out before finishing
Numbers may be suffixed by c (x1), w (x2), b (x512), kD (x1000), k (x1024), MD (x1000000), M (x1048576), GD (x1000000000) or G (x1073741824)
deallocvt [N]
Deallocate unused virtual terminal /dev/ttyN
depmod [-qfwrsv] MODULE [symbol=value...]
Options:
-q Quiet
-f Force
-w Wait for unload
-r Remove module (stacks) or do autoclean
-s Report via syslog instead of stderr
-v Verbose
devmem ADDRESS [WIDTH [VALUE]]
Read/write from physical address
ADDRESS Address to act upon
WIDTH Width (8/16/...)
VALUE Data to be written
df [-Pkmhai] [-B SIZE] [FILESYSTEM...]
Print filesystem usage statistics
Options:
-P POSIX output format
-k 1024-byte blocks (default)
-m 1M-byte blocks
-h Human readable (e.g. 1K 243M 2G)
-a Show all filesystems
-i Inodes
-B SIZE Blocksize
dhcprelay CLIENT_IFACE[,CLIENT_IFACE2...] SERVER_IFACE [SERVER_IP]
Relay DHCP requests between clients and server
diff [-abBdiNqrTstw] [-L LABEL] [-S FILE] [-U LINES] FILE1 FILE2
Compare files line by line and output the differences between them. This implementation supports unified diffs only.
Options:
-a Treat all files as text
-b Ignore changes in the amount of whitespace
-B Ignore changes whose lines are all blank
-d Try hard to find a smaller set of changes
-i Ignore case differences
-L Use LABEL instead of the filename in the unified header
-N Treat absent files as empty
-q Output only whether files differ
-r Recurse
-S Start with FILE when comparing directories
-T Make tabs line up by prefixing a tab when necessary
-s Report when two files are the same
-t Expand tabs to spaces in output
-U Output LINES lines of context
-w Ignore all whitespace
dirname FILENAME
Strip non-directory suffix from FILENAME
dmesg [-c] [-n LEVEL] [-s SIZE]
Print or control the kernel ring buffer
Options:
-c Clear ring buffer after printing
-n LEVEL Set console logging level
-s SIZE Buffer size
dnsd [-c config] [-t seconds] [-p port] [-i iface-ip] [-d]
Small static DNS server daemon
Options:
-c Config filename
-t TTL in seconds
-p Listening port
-i Listening ip (default all)
-d Daemonize
dos2unix [OPTIONS] [FILE]
Convert FILE in-place from DOS to Unix format. When no file is given, use stdin/stdout.
Options:
-u dos2unix
-d unix2dos
dpkg [-ilCPru] [-F option] package_name
Install, remove and manage Debian packages
Options:
-i Install the package
-l List of installed packages
-C Configure an unpackaged package
-F depends Ignore dependency problems
-P Purge all files of a package
-r Remove all but the configuration files for a package
-u Unpack a package, but don't configure it
dpkg-deb [-cefxX] FILE [argument]
Perform actions on Debian packages (.debs)
Options:
-c List contents of filesystem tree
-e Extract control files to [argument] directory
-f Display control field name starting with [argument]
-x Extract packages filesystem tree to directory
-X Verbose extract
du [-aHLdclsxhmk] [FILE]...
Summarize disk space used for each FILE and/or directory. Disk space is printed in units of 1024 bytes.
Options:
-a Show file sizes too
-L Follow all symlinks
-H Follow symlinks on command line
-d N Limit output to directories (and files with -a) of depth < N
-c Show grand total
-l Count sizes many times if hard linked
-s Display only a total for each argument
-x Skip directories on different filesystems
-h Sizes in human readable format (e.g., 1K 243M 2G )
-m Sizes in megabytes
-k Sizes in kilobytes (default)
dumpkmap > keymap
Print a binary keyboard translation table to standard output
dumpleases [-r|-a] [-f LEASEFILE]
Display DHCP leases granted by udhcpd
Options:
-f,--file=FILE Leases file to load
-r,--remaining Interpret lease times as time remaining
-a,--absolute Interpret lease times as expire time
echo [-neE] [ARG...]
Print the specified ARGs to stdout
Options:
-n Suppress trailing newline
-e Interpret backslash-escaped characters (i.e., \t=tab)
-E Disable interpretation of backslash-escaped characters
ed
eject [-t] [-T] [DEVICE]
Eject specified DEVICE (or default /dev/cdrom)
Options:
-s SCSI device
-t Close tray
-T Open/close tray (toggle)
env [-iu] [-] [name=value]... [PROG [ARGS]]
Print the current environment or run PROG after setting up the specified environment
Options:
-, -i Start with an empty environment
-u Remove variable from the environment
envdir dir prog args
Set various environment variables as specified by files in the directory dir and run PROG
envuidgid account prog args
Set $UID to account's uid and $GID to account's gid and run PROG
ether-wake [-b] [-i iface] [-p aa:bb:cc:dd[:ee:ff]] MAC
Send a magic packet to wake up sleeping machines. MAC must be a station address (00:11:22:33:44:55) or a hostname with a known 'ethers' entry.
Options:
-b Send wake-up packet to the broadcast address
-i iface Interface to use (default eth0)
-p pass Append four or six byte password PW to the packet
expand [-i] [-t N] [FILE|-]
Convert tabs to spaces, writing to standard output
Options:
-i,--initial Don't convert tabs after non blanks
-t,--tabs=N Tabstops every N chars
expr EXPRESSION
Print the value of EXPRESSION to standard output
EXPRESSION may be:
ARG1 | ARG2 ARG1 if it is neither null nor 0, otherwise ARG2
ARG1 & ARG2 ARG1 if neither argument is null or 0, otherwise 0
ARG1 < ARG2 1 if ARG1 is less than ARG2, else 0. Similarly:
ARG1 <= ARG2
ARG1 = ARG2
ARG1 != ARG2
ARG1 >= ARG2
ARG1 > ARG2
ARG1 + ARG2 Sum of ARG1 and ARG2. Similarly:
ARG1 - ARG2
ARG1 * ARG2
ARG1 / ARG2
ARG1 % ARG2
STRING : REGEXP Anchored pattern match of REGEXP in STRING
match STRING REGEXP Same as STRING : REGEXP
substr STRING POS LENGTH Substring of STRING, POS counted from 1
index STRING CHARS Index in STRING where any CHARS is found, or 0
length STRING Length of STRING
quote TOKEN Interpret TOKEN as a string, even if
it is a keyword like 'match' or an
operator like '/'
(EXPRESSION) Value of EXPRESSION
Beware that many operators need to be escaped or quoted for shells. Comparisons are arithmetic if both ARGs are numbers, else lexicographical. Pattern matches return the string matched between \( and \) or null; if \( and \) are not used, they return the number of characters matched or 0.
fakeidentd [-fiw] [-b ADDR] [STRING]
Provide fake ident (auth) service
Options:
-f Run in foreground
-i Inetd mode
-w Inetd 'wait' mode
-b ADDR Bind to specified address
STRING Ident answer string (default: nobody)
false
Return an exit code of FALSE (1)
fbset [OPTIONS] [MODE]
Show and modify frame buffer settings
fbsplash -s IMGFILE [-c] [-d DEV] [-i INIFILE] [-f CMD]
Options:
-s Image
-c Hide cursor
-d Framebuffer device (default /dev/fb0)
-i Config file (var=value):
BAR_LEFT,BAR_TOP,BAR_WIDTH,BAR_HEIGHT
BAR_R,BAR_G,BAR_B
-f Control pipe (else exit after drawing image)
commands: 'NN' (% for progress bar) or 'exit'
fdflush DEVICE
Force floppy disk drive to detect disk change
fdformat [-n] DEVICE
Format floppy disk
Options:
-n Don't verify after format
fdisk [-ul] [-C CYLINDERS] [-H HEADS] [-S SECTORS] [-b SSZ] DISK
Change partition table
Options:
-u Start and End are in sectors (instead of cylinders)
-l Show partition table for each DISK, then exit
-b 2048 (for certain MO disks) use 2048-byte sectors
-C CYLINDERS Set number of cylinders/heads/sectors
-H HEADS
-S SECTORS
find [PATH...] [EXPRESSION]
Search for files. The default PATH is the current directory, default EXPRESSION is '-print'
EXPRESSION may consist of:
-follow Follow symlinks
-xdev Don't descend directories on other filesystems
-maxdepth N Descend at most N levels. -maxdepth 0 applies
tests/actions to command line arguments only
-mindepth N Don't act on first N levels
-name PATTERN File name (w/o directory name) matches PATTERN
-iname PATTERN Case insensitive -name
-path PATTERN Path matches PATTERN
-regex PATTERN Path matches regex PATTERN
-type X File type is X (X is one of: f,d,l,b,c,...)
-perm NNN Permissions match any of (+NNN), all of (-NNN),
or exactly NNN
-mtime DAYS Modified time is greater than (+N), less than (-N),
or exactly N days
-mmin MINS Modified time is greater than (+N), less than (-N),
or exactly N minutes
-newer FILE Modified time is more recent than FILE's
-inum N File has inode number N
-user NAME File is owned by user NAME (numeric user ID allowed)
-group NAME File belongs to group NAME (numeric group ID allowed)
-depth Process directory name after traversing it
-size N[bck] File size is N (c:bytes,k:kbytes,b:512 bytes(def.)).
+/-N: file size is bigger/smaller than N
-links N Number of links is greater than (+N), less than (-N),
or exactly N
-print Print (default and assumed)
-print0 Delimit output with null characters rather than
newlines
-exec CMD ARG ; Run CMD with all instances of {} replaced by the
matching files
-prune Stop traversing current subtree
-delete Delete files, turns on -depth option
(EXPR) Group an expression
findfs LABEL=label or UUID=uuid
Find a filesystem device based on a label or UUID
fold [-bs] [-w WIDTH] [FILE]
Wrap input lines in each FILE (standard input by default), writing to standard output
Options:
-b Count bytes rather than columns
-s Break at spaces
-w Use WIDTH columns instead of 80
free
Display the amount of free and used system memory
freeramdisk DEVICE
Free all memory used by the specified ramdisk
fsck [-ANPRTV] [-C fd] [-t fstype] [fs-options] [filesys...]
Check and repair filesystems
Options:
-A Walk /etc/fstab and check all filesystems
-N Don't execute, just show what would be done
-P With -A, check filesystems in parallel
-R With -A, skip the root filesystem
-T Don't show title on startup
-V Verbose
-C n Write status information to specified filedescriptor
-t type List of filesystem types to check
fsck.minix [-larvsmf] /dev/name
Check MINIX filesystem
Options:
-l List all filenames
-r Perform interactive repairs
-a Perform automatic repairs
-v Verbose
-s Output superblock information
-m Show "mode not cleared" warnings
-f Force file system check
fsync [OPTIONS] FILE...Write files' buffered blocks to disk
Options:
-d Avoid syncing metadata
ftpd [-wvS] [-t N] [-T N] [DIR]
Anonymous FTP server
ftpd should be used as an inetd service. ftpd's line for inetd.conf: 21 stream tcp nowait root ftpd ftpd /files/to/serve It also can be ran from tcpsvd:
tcpsvd -vE 0.0.0.0 21 ftpd /files/to/serve
Options:
-w Allow upload
-v Log to stderr
-S Log to syslog
-t,-T Idle and absolute timeouts
DIR Change root to this directory
ftpget [OPTIONS] HOST [LOCAL_FILE] REMOTE_FILE
Retrieve a remote file via FTP
Options:
-c,--continue Continue previous transfer
-v,--verbose Verbose
-u,--username Username
-p,--password Password
-P,--port Port number
ftpput [OPTIONS] HOST [REMOTE_FILE] LOCAL_FILE
Store a local file on a remote machine via FTP
Options:
-v,--verbose Verbose
-u,--username Username
-p,--password Password
-P,--port Port number
fuser [OPTIONS] FILE or PORT/PROTO
Find processes which use FILEs or PORTs
Options:
-m Find processes which use same fs as FILEs
-4 Search only IPv4 space
-6 Search only IPv6 space
-s Silent: just exit with 0 if any processes are found
-k Kill found processes (otherwise display PIDs)
-SIGNAL Signal to send (default: TERM)
getopt [OPTIONS]
Options:
-a,--alternative Allow long options starting with single -
-l,--longoptions=longopts Long options to be recognized
-n,--name=progname The name under which errors are reported
-o,--options=optstring Short options to be recognized
-q,--quiet Disable error reporting by getopt(3)
-Q,--quiet-output No normal output
-s,--shell=shell Set shell quoting conventions
-T,--test Test for getopt(1) version
-u,--unquoted Don't quote the output
grep [-HhrilLnqvsoweFEABCz] PATTERN [FILE]...
Search for PATTERN in each FILE or standard input
Options:
-H Prefix output lines with filename where match was found
-h Suppress the prefixing filename on output
-r Recurse
-i Ignore case distinctions
-l List names of files that match
-L List names of files that don't match
-n Print line number with output lines
-q Quiet. Return 0 if PATTERN is found, 1 otherwise
-v Select non-matching lines
-s Suppress file open/read error messages
-c Only print count of matching lines
-o Show only the part of a line that matches PATTERN
-m N Match up to N times per file
-w Match whole words only
-F PATTERN is a set of newline-separated strings
-E PATTERN is an extended regular expression
-e PTRN Pattern to match
-f FILE Read pattern from file
-A N Print N lines of trailing context
-B N Print N lines of leading context
-C N Print N lines of output context
-z Input is NUL terminated
gunzip [OPTIONS] [FILE]...
Uncompress FILEs (or standard input)
Options:
-c Write to standard output
-f Force
-t Test file integrity
gzip [OPTIONS] [FILE]...
Compress FILEs (or standard input)
Options:
-c Write to standard output
-d Decompress
-f Force
halt [-d DELAY] [-n] [-f] [-w]
Halt the system
Options:
-d Delay interval for halting
-n No call to sync()
-f Force halt (don't go through init)
-w Only write a wtmp record
hd FILE...
hd is an alias for hexdump -C
hdparm [OPTIONS] [DEVICE]
Options:
-a Get/set fs readahead
-A Set drive read-lookahead flag (0/1)
-b Get/set bus state (0 == off, 1 == on, 2 == tristate)
-B Set Advanced Power Management setting (1-255)
-c Get/set IDE 32-bit IO setting
-C Check IDE power mode status
-d Get/set using_dma flag
-D Enable/disable drive defect-mgmt
-f Flush buffer cache for device on exit
-g Display drive geometry
-h Display terse usage information
-i Display drive identification
-I Detailed/current information directly from drive
-k Get/set keep_settings_over_reset flag (0/1)
-K Set drive keep_features_over_reset flag (0/1)
-L Set drive doorlock (0/1) (removable harddisks only)
-m Get/set multiple sector count
-n Get/set ignore-write-errors flag (0/1)
-p Set PIO mode on IDE interface chipset (0,1,2,3,4,...)
-P Set drive prefetch count
-Q Get/set DMA tagged-queuing depth (if supported)
-r Get/set readonly flag (DANGEROUS to set)
-R Register an IDE interface (DANGEROUS)
-S Set standby (spindown) timeout
-t Perform device read timings
-T Perform cache read timings
-u Get/set unmaskirq flag (0/1)
-U Unregister an IDE interface (DANGEROUS)
-v Defaults; same as -mcudkrag for IDE drives
-V Display program version and exit immediately
-w Perform device reset (DANGEROUS)
-W Set drive write-caching flag (0/1) (DANGEROUS)
-x Tristate device for hotswap (0/1) (DANGEROUS)
-X Set IDE xfer mode (DANGEROUS)
-y Put IDE drive in standby mode
-Y Put IDE drive to sleep
-Z Disable Seagate auto-powersaving mode
-z Reread partition table
head [OPTIONS] [FILE]...
Print first 10 lines of each FILE (or standard input) to standard output. With more than one FILE, precede each with a header giving the file name.
Options:
-n N Print first N lines instead of first 10
-c N Output the first N bytes
-q Never output headers giving file names
-v Always output headers giving file names
hexdump [-bcCdefnosvxR] FILE...
Display FILEs or standard input in a user specified format
Options:
-b One-byte octal display
-c One-byte character display
-C Canonical hex+ASCII, 16 bytes per line
-d Two-byte decimal display
-e FORMAT STRING
-f FORMAT FILE
-n LENGTH Interpret only LENGTH bytes of input
-o Two-byte octal display
-s OFFSET Skip OFFSET bytes
-v Display all input data
-x Two-byte hexadecimal display
-R Reverse of 'hexdump -Cv'
hostid
Print out a unique 32-bit identifier for the machine
hostname [OPTIONS] [HOSTNAME | -F FILE]
Get or set hostname or DNS domain name
Options:
-s Short
-i Addresses for the hostname
-d DNS domain name
-f Fully qualified domain name
-F FILE Use FILE's content as hostname
httpd [-ifv[v]] [-c CONFFILE] [-p [IP:]PORT] [-u USER[:GRP]] [-r REALM] [-h HOME] or httpd -d/-e/-m STRING
Listen for incoming HTTP requests
Options:
-i Inetd mode
-f Don't daemonize
-v[v] Verbose
-c FILE Configuration file (default httpd.conf)
-p [IP:]PORT Bind to ip:port (default *:80)
-u USER[:GRP] Set uid/gid after binding to port
-r REALM Authentication Realm for Basic Authentication
-h HOME Home directory (default .)
-m STRING MD5 crypt STRING
-e STRING HTML encode STRING
-d STRING URL decode STRING
hwclock [-r|--show] [-s|--hctosys] [-w|--systohc] [-l|--localtime] [-u|--utc] [-f FILE]
Query and set hardware clock (RTC)
Options:
-r Show hardware clock time
-s Set system time from hardware clock
-w Set hardware clock to system time
-u Hardware clock is in UTC
-l Hardware clock is in local time
-f FILE Use specified device (e.g. /dev/rtc2)
id [OPTIONS] [USER]
Print information about USER or the current user
Options:
-u Print user ID
-g Print group ID
-G Print supplementary group IDs
-n Print name instead of a number
-r Print real user ID instead of effective ID
ifconfig [-a] interface [address]
Configure a network interface
Options:
[add ADDRESS[/PREFIXLEN]]
[del ADDRESS[/PREFIXLEN]]
[[-]broadcast [ADDRESS]] [[-]pointopoint [ADDRESS]]
[netmask ADDRESS] [dstaddr ADDRESS]
[outfill NN] [keepalive NN]
[hw ether|infiniband ADDRESS] [metric NN] [mtu NN]
[[-]trailers] [[-]arp] [[-]allmulti]
[multicast] [[-]promisc] [txqueuelen NN] [[-]dynamic]
[mem_start NN] [io_addr NN] [irq NN]
[up|down] ...
ifdown [-ainmvf] ifaces...
Options:
-a De/configure all interfaces automatically
-i FILE Use FILE for interface definitions
-n Print out what would happen, but don't do it
(note: doesn't disable mappings)
-m Don't run any mappings
-v Print out what would happen before doing it
-f Force de/configuration
ifenslave [-cdf] master-iface <slave-iface...>
Configure network interfaces for parallel routing
Options:
-c, --change-active Change active slave
-d, --detach Remove slave interface from bonding device
-f, --force Force, even if interface is not Ethernet
ifplugd [OPTIONS]
Network interface plug detection daemon
Options:
-n Don't daemonize
-s Don't log to syslog
-i IFACE Interface
-f/-F Treat link detection error as link down/link up
(otherwise exit on error)
-a Don't up interface at each link probe
-M Monitor creation/destruction of interface
(otherwise it must exist)
-r PROG Script to run
-x ARG Extra argument for script
-I Don't exit on nonzero exit code from script
-p Don't run script on daemon startup
-q Don't run script on daemon quit
-l Run script on startup even if no cable is detected
-t SECS Poll time in seconds
-u SECS Delay before running script after link up
-d SECS Delay after link down
-m MODE API mode (mii, priv, ethtool, wlan, iff, auto)
-k Kill running daemon
ifup [-ainmvf] ifaces...
Options:
-a De/configure all interfaces automatically
-i FILE Use FILE for interface definitions
-n Print out what would happen, but don't do it
(note: doesn't disable mappings)
-m Don't run any mappings
-v Print out what would happen before doing it
-f Force de/configuration
inetd [-fe] [-q N] [-R N] [CONFFILE]
Listen for network connections and launch programs
Options:
-f Run in foreground
-e Log to stderr
-q N Socket listen queue (default: 128)
-R N Pause services after N connects/min
(default: 0 - disabled)
init
Init is the parent of all processes
insmod [-qfwrsv] MODULE [symbol=value...]
Options:
-q Quiet
-f Force
-w Wait for unload
-r Remove module (stacks) or do autoclean
-s Report via syslog instead of stderr
-v Verbose
install [-cdDsp] [-o USER] [-g GRP] [-m MODE] [source] dest|directory
Copy files and set attributes
Options:
-c Just copy (default)
-d Create directories
-D Create leading target directories
-s Strip symbol table
-p Preserve date
-o USER Set ownership
-g GRP Set group ownership
-m MODE Set permissions
ionice [-c 1-3] [-n 0-7] [-p PID] [PROG]
Change I/O scheduling class and priority
Options:
-c Class. 1:realtime 2:best-effort 3:idle
-n Priority
ip [OPTIONS] {address | route | link | tunnel | rule} {COMMAND}
ip [OPTIONS] OBJECT {COMMAND} where OBJECT := {address | route | link | tunnel | rule} OPTIONS := { -f[amily] { inet | inet6 | link } | -o[neline] }
| ipaddr { {add|del} IFADDR dev STRING | {show|flush} | |
| [dev STRING] [to PREFIX] } |
ipaddr {add|delete} IFADDR dev STRING ipaddr {show|flush} [dev STRING] [scope SCOPE-ID] [to PREFIX] [label PATTERN] IFADDR := PREFIX | ADDR peer PREFIX [broadcast ADDR] [anycast ADDR] [label STRING] [scope SCOPE-ID] SCOPE-ID := [host | link | global | NUMBER]
ipcalc [OPTIONS] ADDRESS[[/]NETMASK] [NETMASK]
Calculate IP network settings from a IP address
Options:
-b,--broadcast Display calculated broadcast address
-n,--network Display calculated network address
-m,--netmask Display default netmask for IP
-p,--prefix Display the prefix for IP/NETMASK
-h,--hostname Display first resolved host name
-s,--silent Don't ever display error messages
ipcrm [-MQS key] [-mqs id]
Upper-case options MQS remove an object by shmkey value. Lower-case options remove an object by shmid value.
Options:
-mM Remove memory segment after last detach
-qQ Remove message queue
-sS Remove semaphore
ipcs [[-smq] -i shmid] | [[-asmq] [-tcplu]]
-i Show specific resource
Resource specification:
-m Shared memory segments
-q Message queues
-s Semaphore arrays
-a All (default)
Output format:
-t Time
-c Creator
-p Pid
-l Limits
-u Summary
iplink { set DEVICE { up | down | arp { on | off } | show [DEVICE] }
iplink set DEVICE { up | down | arp | multicast { on | off } | dynamic { on | off } | mtu MTU } iplink show [DEVICE]
| iproute { list | flush | { add | del | change | append | | |
| replace | monitor } ROUTE } |
iproute { list | flush } SELECTOR iproute get ADDRESS [from ADDRESS iif STRING] [oif STRING] [tos TOS] iproute { add | del | change | append | replace | monitor } ROUTE SELECTOR := [root PREFIX] [match PREFIX] [proto RTPROTO] ROUTE := [TYPE] PREFIX [tos TOS] [proto RTPROTO] [metric METRIC]
iprule {[list | add | del] RULE}
| iprule [list | add | del] SELECTOR ACTION | |
| SELECTOR := [from PREFIX] [to PREFIX] [tos TOS] [fwmark FWMARK] | |
| [dev STRING] [pref NUMBER] | |
| ACTION := [table TABLE_ID] [nat ADDRESS] | |
| [prohibit | reject | unreachable] | |
| [realms [SRCREALM/]DSTREALM] | |
| TABLE_ID := [local | main | default | NUMBER] |
| iptunnel { add | change | del | show } [NAME] | |
| [mode { ipip | gre | sit }] | |
| [remote ADDR] [local ADDR] [ttl TTL] |
| iptunnel { add | change | del | show } [NAME] | |
| [mode { ipip | gre | sit }] [remote ADDR] [local ADDR] | |
| [[i|o]seq] [[i|o]key KEY] [[i|o]csum] | |
| [ttl TTL] [tos TOS] [[no]pmtudisc] [dev PHYS_DEV] |
kbd_mode [-a|k|s|u] [-C TTY]
Report or set the keyboard mode
Options:
-a Default (ASCII)
-k Medium-raw (keyboard)
-s Raw (scancode)
-u Unicode (utf-8)
-C TTY Affect TTY instead of /dev/tty
kill [-l] [-SIG] PID...
Send a signal (default: TERM) to given PIDs
Options:
-l List all signal names and numbers
killall [-l] [-q] [-SIG] process-name...
Send a signal (default: TERM) to given processes
Options:
-l List all signal names and numbers
-q Don't complain if no processes were killed
killall5 [-l] [-SIG] [-o PID]...
Send a signal (default: TERM) to all processes outside current session
Options:
-l List all signal names and numbers
-o PID Don't signal this PID
klogd [-c N] [-n]
Kernel logger
Options:
-c N Only messages with level < N are printed to console
-n Run in foreground
last [-HW] [-f file]
Show listing of the last users that logged into the system
Options:
-W Display with no host column truncation
-f file Read from file instead of /var/log/wtmp
length STRING
Print STRING's length
less [-EMNmh~I?] [FILE]...
View a file or list of files. The position within files can be changed, and files can be manipulated in various ways.
Options:
-E Quit once the end of a file is reached
-M,-m Display status line with line numbers
and percentage through the file
-N Prefix line number to each line
-I Ignore case in all searches
-~ Suppress ~s displayed past the end of the file
ln [OPTIONS] TARGET... LINK|DIR
Create a link LINK or DIR/TARGET to the specified TARGET(s)
Options:
-s Make symlinks instead of hardlinks
-f Remove existing destinations
-n Don't dereference symlinks - treat like normal file
-b Make a backup of the target (if exists) before link operation
-S suf Use suffix instead of ~ when making backup files
loadfont < font
Load a console font from standard input
loadkmap < keymap
Load a binary keyboard translation table from standard input
logger [OPTIONS] [MESSAGE]
Write MESSAGE to the system log. If MESSAGE is omitted, log stdin.
Options:
-s Log to stderr as well as the system log
-t TAG Log using the specified tag (defaults to user name)
-p PRIO Priority (numeric or facility.level pair)
logname
Print the name of the current user
logread [OPTIONS]
Show messages in syslogd's circular buffer
Options:
-f Output data as log grows
| losetup [-o OFS] LOOPDEV FILE - associate loop devices | |
| losetup -d LOOPDEV - disassociate | |
| losetup [-f] - show |
Options:
-o OFS Start OFS bytes into FILE
-f Show first free loop device
lpd SPOOLDIR [HELPER [ARGS]]
SPOOLDIR must contain (symlinks to) device nodes or directories with names matching print queue names. In the first case, jobs are sent directly to the device. Otherwise each job is stored in queue directory and HELPER program is called. Name of file to print is passed in $DATAFILE variable. Example:
tcpsvd -E 0 515 softlimit -m 999999 lpd /var/spool ./print
lpq [-P queue[@host[:port]]] [-U USERNAME] [-d JOBID...] [-fs]
Options:
-P lp service to connect to (else uses $PRINTER)
-d Delete jobs
-f Force any waiting job to be printed
-s Short display
lpr -P queue[@host[:port]] -U USERNAME -J TITLE -Vmh [FILE]...
Options:
-P lp service to connect to (else uses $PRINTER)
-m Send mail on completion
-h Print banner page too
-V Verbose
ls [-1AacCdeFilnpLRrSsTtuvwxXhk] [FILE]...
List directory contents
Options:
-1 List in a single column
-A Don't list . and ..
-a Don't hide entries starting with .
-C List by columns
-c With -l: sort by ctime
--color[={always,never,auto}] Control coloring
-d List directory entries instead of contents
-e List full date and time
-F Append indicator (one of */=@|) to entries
-i List inode numbers
-l Long listing format
-n List numeric UIDs and GIDs instead of names
-p Append indicator (one of /=@|) to entries
-L List entries pointed to by symlinks
-R Recurse
-r Sort in reverse order
-S Sort by file size
-s List the size of each file, in blocks
-T N Assume tabstop every N columns
-t With -l: sort by modification time
-u With -l: sort by access time
-v Sort by version
-w N Assume the terminal is N columns wide
-x List by lines
-X Sort by extension
-h List sizes in human readable format (1K 243M 2G)
lsattr [-Radlv] [FILE]...
List file attributes on an ext2 fs
Options:
-R Recurse
-a Don't hide entries starting with .
-d List directory entries instead of contents
-l List long flag names
-v List the file's version/generation number
lsmod [-qfwrsv] MODULE [symbol=value...]
Options:
-q Quiet
-f Force
-w Wait for unload
-r Remove module (stacks) or do autoclean
-s Report via syslog instead of stderr
-v Verbose
lspci [-mk]
List all PCI devices
-m Parseable output
-k Show driver
lzmacat FILE
Uncompress to stdout
lzop [-cfvd123456789CF] [FILE]...
-c Write to standard output
-f Force
-v Verbose
-d Decompress
-F Don't store or verify checksum
-C Also write checksum of compressed block
-1..9 Compression level
lzopcat [-vCF] [FILE]...
-v Verbose
-F Don't store or verify checksum
makedevs [-d device_table] rootdir
Create a range of special files as specified in a device table. Device table entries take the form of:
<type> <mode> <uid> <gid> <major> <minor> <start> <inc> <count> Where name is the file name, type can be one of: f Regular file d Directory c Character device b Block device p Fifo (named pipe) uid is the user id for the target file, gid is the group id for the target file. The rest of the entries (major, minor, etc) apply to to device special files. A '-' may be used for blank entries.
makemime [OPTIONS] [FILE]...
Create multipart MIME-encoded message from FILEs
Options:
-o FILE Output. Default: stdout
-a HDR Add header. Examples:
"From: user@host.org", "Date: `date -R`"
-c CT Content type. Default: text/plain
-C CS Charset. Default: us-ascii
Other options are silently ignored
man [OPTIONS] [MANPAGE]...
Format and display manual page
Options:
-a Display all pages
-w Show page locations
md5sum [OPTIONS] [FILE]... or: md5sum [OPTIONS] -c [FILE]
Print or check MD5 checksums
Options:
-c Check sums against given list
-s Don't output anything, status code shows success
-w Warn about improperly formatted checksum lines
mdev [-s]
-s Scan /sys and populate /dev during system boot
It can be run by kernel as a hotplug helper. To activate it: echo /sbin/mdev > /proc/sys/kernel/hotplug It uses /etc/mdev.conf with lines [-]DEVNAME UID:GID PERM [>|=PATH] [@|$|*PROG]
mesg [y|n]
| Control write access to your terminal | ||
| y | Allow write access to your terminal | |
| n | Disallow write access to your terminal |
microcom [-d DELAY] [-t TIMEOUT] [-s SPEED] [-X] TTY
Copy bytes for stdin to TTY and from TTY to stdout
Options:
-d Wait up to DELAY ms for TTY output before sending every
next byte to it
-t Exit if both stdin and TTY are silent for TIMEOUT ms
-s Set serial line to SPEED
-X Disable special meaning of NUL and Ctrl-X from stdin
mkdir [OPTIONS] DIRECTORY...
Create DIRECTORY
Options:
-m Mode
-p No error if exists; make parent directories as needed
mkdosfs [-v] [-n LABEL] BLOCKDEV [KBYTES]
Make a FAT32 filesystem
Options:
-v Verbose
-n LBL Volume label
mkfifo [OPTIONS] name
Create named pipe (identical to 'mknod name p')
Options:
-m MODE Mode (default a=rw)
mkfs.minix [-c | -l filename] [-nXX] [-iXX] BLOCKDEV [KBYTES]
Make a MINIX filesystem
Options:
-c Check device for bad blocks
-n [14|30] Maximum length of filenames
-i INODES Number of inodes for the filesystem
-l FILENAME Read bad blocks list from FILENAME
-v Make version 2 filesystem
mkfs.reiser [-f] [-l LABEL] BLOCKDEV [4K-BLOCKS]
Make a ReiserFS V3 filesystem
Options:
-f Force
-l LBL Volume label
mkfs.vfat [-v] [-n LABEL] BLOCKDEV [KBYTES]
Make a FAT32 filesystem
Options:
-v Verbose
-n LBL Volume label
mknod [OPTIONS] NAME TYPE MAJOR MINOR
Create a special file (block, character, or pipe)
Options:
-m Create the special file using the specified mode (default a=rw)
TYPEs include:
b: Make a block device
c or u: Make a character device
p: Make a named pipe (MAJOR and MINOR are ignored)
mkswap [OPTIONS] BLOCKDEV
Prepare BLOCKDEV to be used as swap partition
Options:
-L LBL Label
mktemp [-dt] [-p DIR] [TEMPLATE]
Create a temporary file with name based on TEMPLATE and print its name. TEMPLATE must end with XXXXXX (e.g. [/dir/]nameXXXXXX).
Options:
-d Make a directory instead of a file
-t Generate a path rooted in temporary directory
-p DIR Use DIR as a temporary directory (implies -t)
For -t or -p, directory is chosen as follows: $TMPDIR if set, else -p DIR, else /tmp
modprobe [-qfwrsv] MODULE [symbol=value...]
Options:
-q Quiet
-f Force
-w Wait for unload
-r Remove module (stacks) or do autoclean
-s Report via syslog instead of stderr
-v Verbose
more [FILE]...
View FILE or standard input one screenful at a time
mount [OPTIONS] [-o OPTS] DEVICE NODE
Mount a filesystem. Filesystem autodetection requires /proc.
Options:
-a Mount all filesystems in fstab
-f Dry run
-r Read-only mount
-w Read-write mount (default)
-t FSTYPE Filesystem type
-O OPT Mount only filesystems with option OPT (-a only)
-o OPT:
loop Ignored (loop devices are autodetected)
[a]sync Writes are [a]synchronous
[no]atime Disable/enable updates to inode access times
[no]diratime Disable/enable atime updates to directories
[no]relatime Disable/enable atime updates relative to modification time
[no]dev (Dis)allow use of special device files
[no]exec (Dis)allow use of executable files
[no]suid (Dis)allow set-user-id-root programs
[r]shared Convert [recursively] to a shared subtree
[r]slave Convert [recursively] to a slave subtree
[r]private Convert [recursively] to a private subtree
[un]bindable Make mount point [un]able to be bind mounted
bind Bind a file or directory to another location
move Relocate an existing mount point
remount Remount a mounted filesystem, changing flags
ro/rw Same as -r/-w
There are filesystem-specific -o flags.
mountpoint [-q] <[-dn] DIR | -x DEVICE>
Check if the directory is a mountpoint
Options:
-q Quiet
-d Print major/minor device number of the filesystem
-n Print device name of the filesystem
-x Print major/minor device number of the blockdevice
mt [-f device] opcode value
Control magnetic tape drive operation
Available Opcodes:
bsf bsfm bsr bss datacompression drvbuffer eof eom erase fsf fsfm fsr fss load lock mkpart nop offline ras1 ras2 ras3 reset retension rewind rewoffline seek setblk setdensity setpart tell unload unlock weof wset
mv [OPTIONS] SOURCE DEST or: mv [OPTIONS] SOURCE... DIRECTORY
Rename SOURCE to DEST, or move SOURCE(s) to DIRECTORY
Options:
-f Don't prompt before overwriting
-i Interactive, prompt before overwrite
nameif [-s] [-c FILE] [{IFNAME MACADDR}]
Rename network interface while it in the down state
Options:
-c FILE Use configuration file (default: /etc/mactab)
-s Use syslog (LOCAL0 facility)
IFNAME MACADDR new_interface_name interface_mac_address
nc [OPTIONS] HOST PORT - connect nc [OPTIONS] -l -p PORT [HOST] [PORT] - listen
Options:
-e PROG Run PROG after connect (must be last)
-l Listen mode, for inbound connects
-n Don't do DNS resolution
-s ADDR Local address
-p PORT Local port
-u UDP mode
-v Verbose
-w SEC Timeout for connects and final net reads
-i SEC Delay interval for lines sent
-o FILE Hex dump traffic
-z Zero-I/O mode (scanning)
netstat [-laentuwxrWp]
Display networking information
Options:
-l Display listening server sockets
-a Display all sockets (default: connected)
-e Display other/more information
-n Don't resolve names
-t Tcp sockets
-u Udp sockets
-w Raw sockets
-x Unix sockets
-r Display routing table
-W Display with no column truncation
-p Display PID/Program name for sockets
nice [-n ADJUST] [PROG [ARGS]]
Run PROG with modified scheduling priority
Options:
-n ADJUST Adjust priority by ADJUST
nmeter format_string
Monitor system in real time
Format specifiers:
%Nc or %[cN] Monitor CPU. N - bar size, default 10
(displays: S:system U:user N:niced D:iowait I:irq i:softirq)
%[niface] Monitor network interface 'iface'
%m Monitor allocated memory
%[mf] Monitor free memory
%[mt] Monitor total memory
%s Monitor allocated swap
%f Monitor number of used file descriptors
%Ni Monitor total/specific IRQ rate
%x Monitor context switch rate
%p Monitor forks
%[pn] Monitor # of processes
%b Monitor block io
%Nt Show time (with N decimal points)
%Nd Milliseconds between updates (default:1000)
%r Print <cr> instead of <lf> at EOL
nohup PROG [ARGS]
Run PROG immune to hangups, with output to a non-tty
nslookup [HOST] [SERVER]
Query the nameserver for the IP address of the given HOST optionally using a specified DNS server
ntpd [-dnqwl] [-S PROG] [-p PEER]...
NTP client/server
Options:
-d Verbose
-n Do not daemonize
-q Quit after clock is set
-w Do not set time (only query peers), implies -n
-l Run as server on port 123
-S PROG Run PROG after stepping time, stratum change, and every 11 mins
-p PEER Obtain time from PEER (may be repeated)
od [-aBbcDdeFfHhIiLlOovXx] [-t TYPE] [FILE]
Write an unambiguous representation, octal bytes by default, of FILE (or standard input) to standard output.
openvt [-c N] [-sw] [PROG [ARGS]]
Start PROG on a new virtual terminal
Options:
-c N Use specified VT
-s Switch to the VT
-w Wait for PROG to exit
patch [OPTIONS] [ORIGFILE [PATCHFILE]]
-p,--strip N Strip N leading components from file names
-i,--input DIFF Read DIFF instead of stdin
-R,--reverse Reverse patch
-N,--forward Ignore already applied patches
--dry-run Don't actually change files
pgrep [-flnovx] [-s SID|-P PPID|PATTERN]
Display process(es) selected by regex PATTERN
Options:
-l Show command name too
-f Match against entire command line
-n Show the newest process only
-o Show the oldest process only
-v Negate the match
-x Match whole name (not substring)
-s Match session ID (0 for current)
-P Match parent process ID
pidof [OPTIONS] [NAME...]
List PIDs of all processes with names that match NAMEs
Options:
-s Show only one PID
-o PID Omit given pid
Use %PPID to omit pid of pidof's parent
ping [OPTIONS] HOST
Send ICMP ECHO_REQUEST packets to network hosts
Options:
-4, -6 Force IP or IPv6 name resolution
-c CNT Send only CNT pings
-s SIZE Send SIZE data bytes in packets (default:56)
-I IFACE/IP Use interface or IP address as source
-W SEC Seconds to wait for the first response (default:10)
(after all -c CNT packets are sent)
-w SEC Seconds until ping exits (default:infinite)
(can exit earlier with -c CNT)
-q Quiet, only displays output at start
and when finished
ping6 [OPTIONS] HOST
Send ICMP ECHO_REQUEST packets to network hosts
Options:
-c CNT Send only CNT pings
-s SIZE Send SIZE data bytes in packets (default:56)
-I IFACE/IP Use interface or IP address as source
-q Quiet, only displays output at start
and when finished
pivot_root NEW_ROOT PUT_OLD
Move the current root file system to PUT_OLD and make NEW_ROOT the new root file system
pkill [-l|-SIGNAL] [-fnovx] [-s SID|-P PPID|PATTERN]
Send a signal to process(es) selected by regex PATTERN
Options:
-l List all signals
-f Match against entire command line
-n Signal the newest process only
-o Signal the oldest process only
-v Negate the match
-x Match whole name (not substring)
-s Match session ID (0 for current)
-P Match parent process ID
popmaildir [OPTIONS] MAILDIR [CONN_HELPER ARGS]
Fetch content of remote mailbox to local maildir
Options:
-s Skip authorization
-T Get messages with TOP instead with RETR
-k Keep retrieved messages on the server
-t SEC Network timeout
-F "PROG ARGS" Filter program. May be multiple
-M "PROG ARGS" Delivery program
poweroff [-d DELAY] [-n] [-f]
Halt and shut off power
Options:
-d Delay interval for halting
-n No call to sync()
-f Force power off (don't go through init)
printenv [VARIABLE...]
Print all or part of environment. If no environment VARIABLE specified, print them all.
printf FORMAT [ARGUMENT...]
Format and print ARGUMENT(s) according to FORMAT, where FORMAT controls the output exactly as in C printf
ps
Report process status
Options:
-o col1,col2=header Select columns for display
-T Show threads
pscan [-cb] [-p MIN_PORT] [-P MAX_PORT] [-t TIMEOUT] [-T MIN_RTT] HOST
Scan a host, print all open ports
Options:
-c Show closed ports too
-b Show blocked ports too
-p Scan from this port (default 1)
-P Scan up to this port (default 1024)
-t Timeout (default 5000 ms)
-T Minimum rtt (default 5 ms, increase for congested hosts)
pwd
Print the full filename of the current working directory
raidautorun DEVICE
Tell the kernel to automatically search and start RAID arrays
rdate [-sp] HOST
Get and possibly set the system date and time from a remote HOST
Options:
-s Set the system date and time (default)
-p Print the date and time
rdev
Print the device node associated with the filesystem mounted at '/'
readahead [FILE]...
Preload FILEs to RAM
readlink [-fnv] FILE
Display the value of a symlink
Options:
-f Canonicalize by following all symlinks
-n Don't add newline
-v Verbose
readprofile [OPTIONS]
Options:
-m mapfile (Default: /boot/System.map)
-p profile (Default: /proc/profile)
-M mult Set the profiling multiplier to mult
-i Print only info about the sampling step
-v Verbose
-a Print all symbols, even if count is 0
-b Print individual histogram-bin counts
-s Print individual counters within functions
-r Reset all the counters (root only)
-n Disable byte order auto-detection
realpath pathname...
Return the absolute pathnames of given argument
reboot [-d DELAY] [-n] [-f]
Reboot the system
Options:
-d Delay interval for rebooting
-n No call to sync()
-f Force reboot (don't go through init)
reformime [OPTIONS] [FILE]...
Parse MIME-encoded message
Options:
-x prefix Extract content of MIME sections to files
-X prog [args] Filter content of MIME sections through prog.
Must be the last option
Other options are silently ignored.
renice {{-n INCREMENT} | PRIORITY} [[-p | -g | -u] ID...]
Change priority of running processes
Options:
-n Adjust current nice value (smaller is faster)
-p Process id(s) (default)
-g Process group id(s)
-u Process user name(s) and/or id(s)
reset
Reset the screen
resize
Resize the screen
rm [OPTIONS] FILE...
Remove (unlink) FILEs
Options:
-i Always prompt before removing
-f Never prompt
-R,-r Recurse
rmdir [OPTIONS] DIRECTORY...
Remove DIRECTORY if it is empty
Options:
-p|--parents Include parents
--ignore-fail-on-non-empty
rmmod [-qfwrsv] MODULE [symbol=value...]
Options:
-q Quiet
-f Force
-w Wait for unload
-r Remove module (stacks) or do autoclean
-s Report via syslog instead of stderr
-v Verbose
route [{add|del|delete}]
Edit kernel routing tables
Options:
-n Don't resolve names
-e Display other/more information
-A inet{6} Select address family
rpm -i -q[ildc]p package.rpm
Manipulate RPM packages
Options:
-i Install package
-q Query package
-p Query uninstalled package
-i Show information
-l List contents
-d List documents
-c List config files
rpm2cpio package.rpm
Output a cpio archive of the rpm file
rtcwake [-a | -l | -u] [-d DEV] [-m MODE] [-s SEC | -t TIME]
Enter a system sleep state until specified wakeup time
-a,--auto Read clock mode from adjtime
-l,--local Clock is set to local time
-u,--utc Clock is set to UTC time
-d,--device=DEV Specify the RTC device
-m,--mode=MODE Set the sleep state (default: standby)
-s,--seconds=SEC Set the timeout in SEC seconds from now
-t,--time=TIME Set the timeout to TIME seconds from epoch
run-parts [-t] [-l] [-a ARG] [-u MASK] DIRECTORY
Run a bunch of scripts in DIRECTORY
Options:
-t Print what would be run, but don't actually run anything
-a ARG Pass ARG as argument for every program
-u MASK Set the umask to MASK before running every program
-l Print names of all matching files even if they are not executable
runlevel [utmp]
Find the current and previous system runlevel
If no utmp file exists or if no runlevel record can be found, print "unknown"
runsv dir
Start and monitor a service and optionally an appendant log service
runsvdir [-P] [-s SCRIPT] dir
Start a runsv process for each subdirectory. If it exits, restart it.
-P Put each runsv in a new session
-s SCRIPT Run SCRIPT <signo> after signal is processed
rx FILE
Receive a file using the xmodem protocol
script [-afqt] [-c PROG] [OUTFILE]
Options:
-a Append output
-c Run PROG, not shell
-f Flush output after each write
-q Quiet
-t Send timing to stderr
scriptreplay timingfile [typescript [divisor]]
Play back typescripts, using timing information
sed [-efinr] SED_CMD [FILE]...
Options:
-e CMD Add CMD to sed commands to be executed
-f FILE Add FILE contents to sed commands to be executed
-i Edit files in-place (else sends result to stdout)
-n Suppress automatic printing of pattern space
-r Use extended regex syntax
If no -e or -f, the first non-option argument is the sed command string. Remaining arguments are input files (stdin if none).
sendmail [OPTIONS] [RECIPIENT_EMAIL]...
Read email from stdin and send it
Standard options:
-t Read additional recipients from message body
-f sender Sender (required)
-o options Various options. -oi implied, others are ignored
-i -oi synonym. implied and ignored
Busybox specific options:
-w seconds Network timeout
-H 'PROG ARGS' Run connection helper
Examples:
-H 'exec openssl s_client -quiet -tls1 -starttls smtp
-connect smtp.gmail.com:25' <email.txt
[4<username_and_passwd.txt | -au<username> -ap<password>]
-H 'exec openssl s_client -quiet -tls1
-connect smtp.gmail.com:465' <email.txt
[4<username_and_passwd.txt | -au<username> -ap<password>]
-S server[:port] Server
-au<username> Username for AUTH LOGIN
-ap<password> Password for AUTH LOGIN
-am<method> Authentication method. Ignored. LOGIN is implied
Other options are silently ignored; -oi -t is implied Use makemime applet to create message with attachments
seq [-w] [-s SEP] [FIRST [INC]] LAST
Print numbers from FIRST to LAST, in steps of INC. FIRST, INC default to 1
Options:
-w Pad to last with leading zeros
-s SEP String separator
setarch personality program [args...]
Personality may be:
linux32 Set 32bit uname emulation
linux64 Set 64bit uname emulation
setconsole [-r|--reset] [DEVICE]
Redirect system console output to DEVICE (default: /dev/tty)
Options:
-r Reset output to /dev/console
setfont FONT [-m MAPFILE] [-C TTY]
Load a console font
Options:
-m MAPFILE Load console screen map
-C TTY Affect TTY instead of /dev/tty
setkeycodes SCANCODE KEYCODE...
Set entries into the kernel's scancode-to-keycode map, allowing unusual keyboards to generate usable keycodes.
SCANCODE may be either xx or e0xx (hexadecimal), and KEYCODE is given in decimal
setlogcons N
Redirect the kernel output to console N (0 for current)
setsid PROG [ARG...]
Run PROG in a new session. PROG will have no controlling terminal
and will not be affected by keyboard signals (Ctrl-C etc).
See setsid(2) for details.
setuidgid account prog args
Set uid and gid to account's uid and gid, removing all supplementary groups and run PROG
sha1sum [OPTIONS] [FILE]... or: sha1sum [OPTIONS] -c [FILE]
Print or check SHA1 checksums
Options:
-c Check sums against given list
-s Don't output anything, status code shows success
-w Warn about improperly formatted checksum lines
sha256sum [OPTIONS] [FILE]... or: sha256sum [OPTIONS] -c [FILE]
Print or check SHA256 checksums
Options:
-c Check sums against given list
-s Don't output anything, status code shows success
-w Warn about improperly formatted checksum lines
sha512sum [OPTIONS] [FILE]... or: sha512sum [OPTIONS] -c [FILE]
Print or check SHA512 checksums
Options:
-c Check sums against given list
-s Don't output anything, status code shows success
-w Warn about improperly formatted checksum lines
showkey [-a | -k | -s]
Show keys pressed
Options:
-a Display decimal/octal/hex values of the keys
-k Display interpreted keycodes (default)
-s Display raw scan-codes
slattach [-cehmLF] [-s SPEED] [-p PROTOCOL] DEVICE
Attach network interface(s) to serial line(s)
Options:
-p PROT Set protocol (slip, cslip, slip6, clisp6 or adaptive)
-s SPD Set line speed
-e Exit after initializing device
-h Exit when the carrier is lost
-c PROG Run PROG when the line is hung up
-m Do NOT initialize the line in raw 8 bits mode
-L Enable 3-wire operation
-F Disable RTS/CTS flow control
sleep [N]...
Pause for a time equal to the total of the args given, where each arg can have an optional suffix of (s)econds, (m)inutes, (h)ours, or (d)ays
| softlimit [-a BYTES] [-m BYTES] [-d BYTES] [-s BYTES] [-l BYTES] | |
| [-f BYTES] [-c BYTES] [-r BYTES] [-o N] [-p N] [-t N] | |
| PROG ARGS |
Set soft resource limits, then run PROG
Options:
-a BYTES Limit total size of all segments
-m BYTES Same as -d BYTES -s BYTES -l BYTES -a BYTES
-d BYTES Limit data segment
-s BYTES Limit stack segment
-l BYTES Limit locked memory size
-o N Limit number of open files per process
-p N Limit number of processes per uid
Options controlling file sizes:
-f BYTES Limit output file sizes
-c BYTES Limit core file size
Efficiency opts:
-r BYTES Limit resident set size
-t N Limit CPU time, process receives
a SIGXCPU after N seconds
sort [-nrugMcszbdfimSTokt] [-o FILE] [-k start[.offset][opts][,end[.offset][opts]] [-t CHAR] [FILE]...
Sort lines of text
Options:
-b Ignore leading blanks
-c Check whether input is sorted
-d Dictionary order (blank or alphanumeric only)
-f Ignore case
-g General numerical sort
-i Ignore unprintable characters
-k Sort key
-M Sort month
-n Sort numbers
-o Output to file
-k Sort by key
-t CHAR Key separator
-r Reverse sort order
-s Stable (don't sort ties alphabetically)
-u Suppress duplicate lines
-z Lines are terminated by NUL, not newline
-mST Ignored for GNU compatibility
split [OPTIONS] [INPUT [PREFIX]]
Options:
-b n[k|m] Split by bytes
-l n Split by lines
-a n Use n letters as suffix
start-stop-daemon [OPTIONS] [-S|-K] ... [-- arguments...]
Search for matching processes, and then -K: stop all matching processes. -S: start a process unless a matching process is found.
Process matching:
-u,--user USERNAME|UID Match only this user's processes
-n,--name NAME Match processes with NAME
in comm field in /proc/PID/stat
-x,--exec EXECUTABLE Match processes with this command
in /proc/PID/cmdline
-p,--pidfile FILE Match a process with PID from the file
All specified conditions must match
-S only:
-x,--exec EXECUTABLE Program to run
-a,--startas NAME Zeroth argument
-b,--background Background
-N,--nicelevel N Change nice level
-c,--chuid USER[:[GRP]] Change to user/group
-m,--make-pidfile Write PID to the pidfile specified by -p
-K only:
-s,--signal SIG Signal to send
-t,--test Match only, exit with 0 if a process is found
Other:
-o,--oknodo Exit with status 0 if nothing is done
-v,--verbose Verbose
-q,--quiet Quiet
stat [OPTIONS] FILE...
Display file (default) or filesystem status
Options:
-c fmt Use the specified format
-f Display filesystem status
-L Follow links
-t Display info in terse form
Valid format sequences for files:
%a Access rights in octal %A Access rights in human readable form %b Number of blocks allocated (see %B) %B The size in bytes of each block reported by %b %d Device number in decimal %D Device number in hex %f Raw mode in hex %F File type %g Group ID of owner %G Group name of owner %h Number of hard links %i Inode number %n File name %N File name, with -> TARGET if symlink %o I/O block size %s Total size, in bytes %t Major device type in hex %T Minor device type in hex %u User ID of owner %U User name of owner %x Time of last access %X Time of last access as seconds since Epoch %y Time of last modification %Y Time of last modification as seconds since Epoch %z Time of last change %Z Time of last change as seconds since Epoch
Valid format sequences for file systems:
%a Free blocks available to non-superuser %b Total data blocks in file system %c Total file nodes in file system %d Free file nodes in file system %f Free blocks in file system %i File System ID in hex %l Maximum length of filenames %n File name %s Block size (for faster transfer) %S Fundamental block size (for block counts) %t Type in hex %T Type in human readable form
strings [-afo] [-n LEN] [FILE]...
Display printable strings in a binary file
Options:
-a Scan whole file (default)
-f Precede strings with filenames
-n LEN At least LEN characters form a string (default 4)
-o Precede strings with decimal offsets
stty [-a|g] [-F DEVICE] [SETTING]...
Without arguments, prints baud rate, line discipline, and deviations from stty sane
Options:
-F DEVICE Open device instead of stdin
-a Print all current settings in human-readable form
-g Print in stty-readable form
[SETTING] See manpage
sum [-rs] [FILE]...
Checksum and count the blocks in a file
Options:
-r Use BSD sum algorithm (1K blocks)
-s Use System V sum algorithm (512byte blocks)
sv [-v] [-w SEC] command service...
Control services monitored by runsv supervisor. Commands (only first character is enough):
status: query service status up: if service isn't running, start it. If service stops, restart it once: like 'up', but if service stops, don't restart it down: send TERM and CONT signals. If ./run exits, start ./finish if it exists. After it stops, don't restart service exit: send TERM and CONT signals to service and log service. If they exit, runsv exits too pause, cont, hup, alarm, interrupt, quit, 1, 2, term, kill: send STOP, CONT, HUP, ALRM, INT, QUIT, USR1, USR2, TERM, KILL signal to service
svlogd [-ttv] [-r c] [-R abc] [-l len] [-b buflen] dir...
Continuously read log data from standard input, optionally filter log messages, and write the data to one or more automatically rotated logs
swapoff [-a] [DEVICE]
Stop swapping on DEVICE
Options:
-a Stop swapping on all swap devices
swapon [-a] [-p PRI] [DEVICE]
Start swapping on DEVICE
Options:
-a Start swapping on all swap devices
-p PRI Set swap device priority
switch_root [-c /dev/console] NEW_ROOT NEW_INIT [ARGS]
Free initramfs and switch to another root fs:
chroot to NEW_ROOT, delete all in /, move NEW_ROOT to /, execute NEW_INIT. PID must be 1. NEW_ROOT must be a mountpoint.
Options:
-c DEV Reopen stdio to DEV after switch
sync
Write all buffered blocks to disk
sysctl [OPTIONS] [VALUE]...
Configure kernel parameters at runtime
Options:
-n Don't print key names
-e Don't warn about unknown keys
-w Change sysctl setting
-p FILE Load sysctl settings from FILE (default /etc/sysctl.conf)
-a Display all values
-A Display all values in table form
syslogd [OPTIONS]
System logging utility. Note that this version of syslogd ignores /etc/syslog.conf.
Options:
-n Run in foreground
-O FILE Log to given file (default:/var/log/messages)
-l n Set local log level
-S Smaller logging output
-s SIZE Max size (KB) before rotate (default:200KB, 0=off)
-b N N rotated logs to keep (default:1, max=99, 0=purge)
-R HOST[:PORT] Log to IP or hostname on PORT (default PORT=514/UDP)
-L Log locally and via network (default is network only if -R)
-D Drop duplicates
-C[size(KiB)] Log to shared mem buffer (read it using logread)
tac [FILE]...
Concatenate FILEs and print them in reverse
tail [OPTIONS] [FILE]...
Print last 10 lines of each FILE (or standard input) to standard output. With more than one FILE, precede each with a header giving the file name.
Options:
-c N[kbm] Output last N bytes
-n N[kbm] Print last N lines instead of last 10
-f Output data as the file grows
-q Never output headers giving file names
-s SEC Wait SEC seconds between reads with -f
-v Always output headers giving file names
If the first character of N (bytes or lines) is a '+', output begins with the Nth item from the start of each file, otherwise, print the last N items in the file. N bytes may be suffixed by k (x1024), b (x512), or m (1024^2).
tar -[cxtzjaZmvO] [-X FILE] [-f TARFILE] [-C DIR] [FILE]...
Create, extract, or list files from a tar file
Options:
c Create
x Extract
t List
Archive format selection:
z Filter the archive through gzip
j Filter the archive through bzip2
a Filter the archive through lzma
Z Filter the archive through compress
m Do not restore mtime
File selection:
f Name of TARFILE or "-" for stdin
O Extract to stdout
exclude File to exclude
X File with names to exclude
C Change to DIR before operation
v Verbose
taskset [-p] [MASK] [PID | PROG [ARGS]]
Set or get CPU affinity
Options:
-p Operate on an existing PID
tcpsvd [-hEv] [-c N] [-C N[:MSG]] [-b N] [-u USER] [-l NAME] IP PORT PROG
Create TCP socket, bind to IP:PORT and listen for incoming connection. Run PROG for each connection.
IP IP to listen on. '0' = all
PORT Port to listen on
PROG [ARGS] Program to run
-l NAME Local hostname (else looks up local hostname in DNS)
-u USER[:GRP] Change to user/group after bind
-c N Handle up to N connections simultaneously
-b N Allow a backlog of approximately N TCP SYNs
-C N[:MSG] Allow only up to N connections from the same IP
New connections from this IP address are closed
immediately. MSG is written to the peer before close
-h Look up peer's hostname
-E Don't set up environment variables
-v Verbose
tee [OPTIONS] [FILE]...
Copy standard input to each FILE, and also to standard output
Options:
-a Append to the given FILEs, don't overwrite
-i Ignore interrupt signals (SIGINT)
telnet [-a] [-l USER] HOST [PORT]
Connect to telnet server
Options:
-a Automatic login with $USER variable
-l USER Automatic login as USER
telnetd [OPTIONS]
Handle incoming telnet connections
Options:
-l LOGIN Exec LOGIN on connect
-f ISSUE_FILE Display ISSUE_FILE instead of /etc/issue
-K Close connection as soon as login exits
(normally wait until all programs close slave pty)
-p PORT Port to listen on
-b ADDR[:PORT] Address to bind to
-F Run in foreground
-i Run as inetd service
test EXPRESSION ]
Check file types, compare values etc. Return a 0/1 exit code depending on logical value of EXPRESSION
tftp [OPTIONS] HOST [PORT]
Transfer a file from/to tftp server
Options:
-l FILE Local FILE
-r FILE Remote FILE
-g Get file
-p Put file
-b SIZE Transfer blocks of SIZE octets
tftpd [-cr] [-u USER] [DIR]
Transfer a file on tftp client's request
tftpd should be used as an inetd service. tftpd's line for inetd.conf: 69 dgram udp nowait root tftpd tftpd /files/to/serve It also can be ran from udpsvd:
udpsvd -vE 0.0.0.0 69 tftpd /files/to/serve
Options:
-r Prohibit upload
-c Allow file creation via upload
-u Access files as USER
time [OPTIONS] PROG [ARGS]
Run PROG. When it finishes, its resource usage is displayed.
Options:
-v Verbose
timeout [-t SECS] [-s SIG] PROG [ARGS]
Runs PROG. Sends SIG to it if it is not gone in SECS seconds. Defaults: SECS: 10, SIG: TERM.
top [-b] [-nCOUNT] [-dSECONDS] [-m]
Provide a view of process activity in real time. Read the status of all processes from /proc each SECONDS and show the status for however many processes will fit on the screen.
touch [-c] [-d DATE] FILE [FILE]...
Update the last-modified date on the given FILE[s]
Options:
-c Don't create files
-d DT Date/time to use
tr [-cds] STRING1 [STRING2]
Translate, squeeze, and/or delete characters from standard input, writing to standard output
Options:
-c Take complement of STRING1
-d Delete input characters coded STRING1
-s Squeeze multiple output characters of STRING2 into one character
| traceroute [-46FIldnrv] [-f 1ST_TTL] [-m MAXTTL] [-p PORT] [-q PROBES] | |
| [-s SRC_IP] [-t TOS] [-w WAIT_SEC] [-g GATEWAY] [-i IFACE] | |
| [-z PAUSE_MSEC] HOST [BYTES] |
Trace the route to HOST
Options:
-4, -6 Force IP or IPv6 name resolution
-F Set the don't fragment bit
-I Use ICMP ECHO instead of UDP datagrams
-l Display the ttl value of the returned packet
-d Set SO_DEBUG options to socket
-n Print numeric addresses
-r Bypass routing tables, send directly to HOST
-v Verbose
-m Max time-to-live (max number of hops)
-p Base UDP port number used in probes
(default 33434)
-q Number of probes per 'ttl' (default 3)
-s IP address to use as the source address
-t Type-of-service in probe packets (default 0)
-w Time in seconds to wait for a response (default 3)
-g Loose source route gateway (8 max)
| traceroute6 [-dnrv] [-m MAXTTL] [-p PORT] [-q PROBES] | |
| [-s SRC_IP] [-t TOS] [-w WAIT_SEC] [-i IFACE] | |
| HOST [BYTES] |
Trace the route to HOST
Options:
-d Set SO_DEBUG options to socket
-n Print numeric addresses
-r Bypass routing tables, send directly to HOST
-v Verbose
-m Max time-to-live (max number of hops)
-p Base UDP port number used in probes
(default is 33434)
-q Number of probes per 'ttl' (default 3)
-s IP address to use as the source address
-t Type-of-service in probe packets (default 0)
-w Time in seconds to wait for a response (default 3)
true
Return an exit code of TRUE (0)
tty
Print file name of standard input's terminal
ttysize [w] [h]
Print dimension(s) of standard input's terminal, on error return 80x25
tunctl [-f device] ([-t name] | -d name) [-u owner] [-g group] [-b]
Create or delete tun interfaces
Options:
-f name tun device (/dev/net/tun)
-t name Create iface 'name'
-d name Delete iface 'name'
-u owner Set iface owner
-g group Set iface group
-b Brief output
| udhcpc [-Cfbnqtvo] [-c CID] [-V VCLS] [-H HOSTNAME] [-i INTERFACE] | |
| [-p pidfile] [-r IP] [-s script] [-O dhcp-option]... [-P N] |
-V,--vendorclass=CLASSID Vendor class identifier
-i,--interface=INTERFACE Interface to use (default eth0)
-H,-h,--hostname=HOSTNAME Client hostname
-c,--clientid=CLIENTID Client identifier
-C,--clientid-none Suppress default client identifier
-p,--pidfile=FILE Create pidfile
-r,--request=IP IP address to request
-s,--script=FILE Run FILE at DHCP events (default /usr/share/udhcpc/default.script)
-t,--retries=N Send up to N discover packets
-T,--timeout=N Pause between packets (default 3 seconds)
-A,--tryagain=N Wait N seconds (default 20) after failure
-O,--request-option=OPT Request DHCP option OPT (cumulative)
-o,--no-default-options Don't request any options (unless -O is also given)
-f,--foreground Run in foreground
-b,--background Background if lease is not immediately obtained
-S,--syslog Log to syslog too
-n,--now Exit with failure if lease is not immediately obtained
-q,--quit Quit after obtaining lease
-R,--release Release IP on quit
-P,--client-port N Use port N instead of default 68
-a,--arping Use arping to validate offered address
udhcpd [-fS] [-P N] [configfile]
DHCP server
-f Run in foreground
-S Log to syslog too
-P N Use port N instead of default 67
udpsvd [-hEv] [-c N] [-u USER] [-l NAME] IP PORT PROG
Create UDP socket, bind to IP:PORT and wait for incoming packets. Run PROG for each packet, redirecting all further packets with same peer ip:port to it.
IP IP to listen on. '0' = all
PORT Port to listen on
PROG [ARGS] Program to run
-l NAME Local hostname (else looks up local hostname in DNS)
-u USER[:GRP] Change to user/group after bind
-c N Handle up to N connections simultaneously
-h Look up peer's hostname
-E Don't set up environment variables
-v Verbose
umount [OPTIONS] FILESYSTEM|DIRECTORY
Unmount file systems
Options:
-a Unmount all file systems
-r Try to remount devices as read-only if mount is busy
-l Lazy umount (detach filesystem)
-f Force umount (i.e., unreachable NFS server)
-d Free loop device if it has been used
uname [-amnrspv]
Print system information
Options:
-a Print all
-m The machine (hardware) type
-n Hostname
-r OS release
-s OS name (default)
-p Processor type
-v OS version
uncompress [-c] [-f] [FILE...]
Uncompress .Z file[s]
Options:
-c Extract to stdout
-f Overwrite an existing file
unexpand [-f][-a][-t N] [FILE|-]
Convert spaces to tabs, writing to standard output
Options:
-a,--all Convert all blanks
-f,--first-only Convert only leading blanks
-t,--tabs=N Tabstops every N chars
uniq [-fscduw]... [INPUT [OUTPUT]]
Discard duplicate lines
Options:
-c Prefix lines by the number of occurrences
-d Only print duplicate lines
-u Only print unique lines
-f N Skip first N fields
-s N Skip first N chars (after any skipped fields)
-w N Compare N characters in line
unix2dos [OPTIONS] [FILE]
Convert FILE in-place from Unix to DOS format. When no file is given, use stdin/stdout.
Options:
-u dos2unix
-d unix2dos
unlzma [OPTIONS] [FILE]
Uncompress FILE (or standard input)
Options:
-c Write to standard output
-f Force
unlzop [-cfvCF] [FILE]...
-c Write to standard output
-f Force
-v Verbose
-F Don't store or verify checksum
unzip [-opts[modifiers]] file[.zip] [list] [-x xlist] [-d exdir]
Extract files from ZIP archives
Options:
-l List archive contents (with -q for short form)
-n Never overwrite existing files (default)
-o Overwrite files without prompting
-p Send output to stdout
-q Quiet
-x Exclude these files
-d Extract files into this directory
uptime
Display the time since the last boot
usleep N
Pause for N microseconds
uudecode [-o OUTFILE] [INFILE]
Uudecode a file Finds outfile name in uuencoded source unless -o is given
uuencode [-m] [INFILE] STORED_FILENAME
Uuencode a file to stdout
Options:
-m Use base64 encoding per RFC1521
vconfig COMMAND [OPTIONS]
Create and remove virtual ethernet devices
Options:
add [interface-name] [vlan_id]
rem [vlan-name]
set_flag [interface-name] [flag-num] [0 | 1]
set_egress_map [vlan-name] [skb_priority] [vlan_qos]
set_ingress_map [vlan-name] [skb_priority] [vlan_qos]
set_name_type [name-type]
vi [OPTIONS] [FILE]...
Edit FILE
Options:
-c Initial command to run ($EXINIT also available)
-R Read-only
-H Short help regarding available features
volname [DEVICE]
Show CD volume name of the DEVICE (default /dev/cdrom)
wall [FILE]
Write content of FILE or standard-input to all logged-in users
watch [-n seconds] [-t] PROG [ARGS]
Run PROG periodically
Options:
-n Loop period in seconds (default 2)
-t Don't print header
watchdog [-t N[ms]] [-T N[ms]] [-F] DEV
Periodically write to watchdog device DEV
Options:
-T N Reboot after N seconds if not reset (default 60)
-t N Reset every N seconds (default 30)
-F Run in foreground
Use 500ms to specify period in milliseconds
wc [OPTIONS] [FILE]...
Print line, word, and byte counts for each FILE, and a total line if more than one FILE is specified. With no FILE, read standard input.
Options:
-c Print the byte counts
-l Print the newline counts
-L Print the length of the longest line
-w Print the word counts
| wget [-c|--continue] [-s|--spider] [-q|--quiet] [-O|--output-document file] | |
| [--header 'header: value'] [-Y|--proxy on/off] [-P DIR] | |
| [-U|--user-agent agent] url |
Retrieve files via HTTP or FTP
Options:
-s Spider mode - only check file existence
-c Continue retrieval of aborted transfer
-q Quiet
-P Set directory prefix to DIR
-O Save to filename ('-' for stdout)
-U Adjust 'User-Agent' field
-Y Use proxy ('on' or 'off')
which [COMMAND]...
Locate a COMMAND
who [-a]
Show who is logged on
Options:
-a show all
whoami
Print the user name associated with the current effective user id
xargs [OPTIONS] [PROG [ARGS]]
Run PROG on every item given by standard input
Options:
-p Ask user whether to run each command
-r Don't run command if input is empty
-0 Input is separated by NUL characters
-t Print the command on stderr before execution
-e[STR] STR stops input processing
-n N Pass no more than N args to PROG
-s N Pass command line of no more than N bytes
-x Exit if size is exceeded
yes [OPTIONS] [STRING]
Repeatedly output a line with STRING, or 'y'
zcat FILE
Uncompress to stdout
zcip [OPTIONS] IFACE SCRIPT
Manage a ZeroConf IPv4 link-local address
Options:
-f Run in foreground
-q Quit after obtaining address
-r 169.254.x.x Request this address first
-v Verbose
With no -q, runs continuously monitoring for ARP conflicts, exits only on I/O errors (link down etc)
GNU Libc (glibc) uses the Name Service Switch (NSS) to configure the behavior of the C library for the local environment, and to configure how it reads system data, such as passwords and group information. This is implemented using an /etc/nsswitch.conf configuration file, and using one or more of the /lib/libnss_* libraries. BusyBox tries to avoid using any libc calls that make use of NSS. Some applets however, such as login and su, will use libc functions that require NSS.
If you enable CONFIG_USE_BB_PWD_GRP, BusyBox will use internal functions to directly access the /etc/passwd, /etc/group, and /etc/shadow files without using NSS. This may allow you to run your system without the need for installing any of the NSS configuration files and libraries.
When used with glibc, the BusyBox 'networking' applets will similarly require that you install at least some of the glibc NSS stuff (in particular, /etc/nsswitch.conf, /lib/libnss_dns*, /lib/libnss_files*, and /lib/libresolv*).
Shameless Plug: As an alternative, one could use a C library such as uClibc. In addition to making your system significantly smaller, uClibc does not require the use of any NSS support files or libraries.
Denis Vlasenko <vda.linux@googlemail.com>
The following people have contributed code to BusyBox whether they know it or not. If you have written code included in BusyBox, you should probably be listed here so you can obtain your bit of eternal glory. If you should be listed here, or the description of what you have done needs more detail, or is incorrect, please send in an update.
Emanuele Aina <emanuele.aina@tiscali.it> run-parts
Erik Andersen <andersen@codepoet.org>
Tons of new stuff, major rewrite of most of the
core apps, tons of new apps as noted in header files.
Lots of tedious effort writing these boring docs that
nobody is going to actually read.
Laurence Anderson <l.d.anderson@warwick.ac.uk>
rpm2cpio, unzip, get_header_cpio, read_gz interface, rpm
Jeff Angielski <jeff@theptrgroup.com>
ftpput, ftpget
Edward Betts <edward@debian.org>
expr, hostid, logname, whoami
John Beppu <beppu@codepoet.org>
du, nslookup, sort
Brian Candler <B.Candler@pobox.com>
tiny-ls(ls)
Randolph Chung <tausq@debian.org>
fbset, ping, hostname
Dave Cinege <dcinege@psychosis.com>
more(v2), makedevs, dutmp, modularization, auto links file,
various fixes, Linux Router Project maintenance
Jordan Crouse <jordan@cosmicpenguin.net>
ipcalc
Magnus Damm <damm@opensource.se>
tftp client insmod powerpc support
Larry Doolittle <ldoolitt@recycle.lbl.gov>
pristine source directory compilation, lots of patches and fixes.
Glenn Engel <glenne@engel.org>
httpd
Gennady Feldman <gfeldman@gena01.com>
Sysklogd (single threaded syslogd, IPC Circular buffer support,
logread), various fixes.
Karl M. Hegbloom <karlheg@debian.org>
cp_mv.c, the test suite, various fixes to utility.c, &c.
Daniel Jacobowitz <dan@debian.org>
mktemp.c
Matt Kraai <kraai@alumni.cmu.edu>
documentation, bugfixes, test suite
Stephan Linz <linz@li-pro.net>
ipcalc, Red Hat equivalence
John Lombardo <john@deltanet.com>
tr
Glenn McGrath <bug1@iinet.net.au>
Common unarchiving code and unarchiving applets, ifupdown, ftpgetput,
nameif, sed, patch, fold, install, uudecode.
Various bugfixes, review and apply numerous patches.
Manuel Novoa III <mjn3@codepoet.org>
cat, head, mkfifo, mknod, rmdir, sleep, tee, tty, uniq, usleep, wc, yes,
mesg, vconfig, make_directory, parse_mode, dirname, mode_string,
get_last_path_component, simplify_path, and a number trivial libbb routines
also bug fixes, partial rewrites, and size optimizations in
ash, basename, cal, cmp, cp, df, du, echo, env, ln, logname, md5sum, mkdir,
mv, realpath, rm, sort, tail, touch, uname, watch, arith, human_readable,
interface, dutmp, ifconfig, route
Vladimir Oleynik <dzo@simtreas.ru>
cmdedit; xargs(current), httpd(current);
ports: ash, crond, fdisk, inetd, stty, traceroute, top;
locale, various fixes
and irreconcilable critic of everything not perfect.
Bruce Perens <bruce@pixar.com>
Original author of BusyBox in 1995, 1996. Some of his code can
still be found hiding here and there...
Tim Riker <Tim@Rikers.org>
bug fixes, member of fan club
Kent Robotti <robotti@metconnect.com>
reset, tons and tons of bug reports and patches.
Chip Rosenthal <chip@unicom.com>, <crosenth@covad.com>
wget - Contributed by permission of Covad Communications
Pavel Roskin <proski@gnu.org>
Lots of bugs fixes and patches.
Gyepi Sam <gyepi@praxis-sw.com>
Remote logging feature for syslogd
Linus Torvalds <torvalds@transmeta.com>
mkswap, fsck.minix, mkfs.minix
Mark Whitley <markw@codepoet.org>
grep, sed, cut, xargs(previous),
style-guide, new-applet-HOWTO, bug fixes, etc.
Charles P. Wright <cpwright@villagenet.com>
gzip, mini-netcat(nc)
Enrique Zanardi <ezanardi@ull.es>
tarcat (since removed), loadkmap, various fixes, Debian maintenance
Tito Ragusa <farmatito@tiscali.it>
devfsd and size optimizations in strings, openvt and deallocvt.